Yuex.S's Replies | Sysprogs

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 27 total)

1 2 →

Author

Posts
May 29, 2018 at 13:43 in reply to: How to use your own cloned ESP-IDF #21020

Yuex.S
Participant

I cloned it with the command below.
git clone –recursive -b release/v3.0 https://github.com/espressif/esp-idf.git

Cannot be used properly after cloning.

March 15, 2018 at 11:30 in reply to: Authorization is not available after reinstalling the computer system #20430

Yuex.S
Participant

Just tested, and now it’s ready to activate, thank you very much.

March 15, 2018 at 09:43 in reply to: Authorization is not available after reinstalling the computer system #20427

Yuex.S
Participant

How long can I handle it? I’ve never received an email with my email address changed to Gmail.

March 15, 2018 at 06:59 in reply to: Authorization is not available after reinstalling the computer system #20426

Yuex.S
Participant

I’ve been using Gmail mail again.

March 15, 2018 at 06:40 in reply to: Authorization is not available after reinstalling the computer system #20425

Yuex.S
Participant

Is this email just a feedback message?

March 15, 2018 at 05:07 in reply to: Authorization is not available after reinstalling the computer system #20422

Yuex.S
Participant

I rewrote a mailbox address and submitted it

March 15, 2018 at 05:02 in reply to: Authorization is not available after reinstalling the computer system #20421

Yuex.S
Participant

So what else do I need to do

March 15, 2018 at 04:05 in reply to: Authorization is not available after reinstalling the computer system #20415

Yuex.S
Participant

Should I submit it for another email?

March 14, 2018 at 18:43 in reply to: Authorization is not available after reinstalling the computer system #20400

Yuex.S
Participant

Support has been submitted. Thank you.

November 9, 2017 at 11:33 in reply to: How does the generated bin file burn into the motherboard? #12919

Yuex.S
Participant

Excuse me, is ESPImageTool.exe open source?

November 9, 2017 at 11:22 in reply to: How does the generated bin file burn into the motherboard? #12918

Yuex.S
Participant

I clicked the “program and start Without debuging” and became a two “<project name>-<Offset>. bin” file that has been written to normal, thanks very much.

November 9, 2017 at 11:04 in reply to: How does the generated bin file burn into the motherboard? #12917

Yuex.S
Participant

Hello, where is <offset> generated, and not seen.

November 9, 2017 at 05:12 in reply to: How does the generated bin file burn into the motherboard? #12908

Yuex.S
Participant

But the file I generated is not “<Project Name>-<Offset>.bin” syntax. Is it something that needs to be set?
The file I generated is just “<Project Name>.bin” syntax

November 1, 2017 at 17:33 in reply to: Serial output is garbled #12811

Yuex.S
Participant

Thanks very much, the baud rate and the program did not empty the flash cause.

October 31, 2017 at 11:09 in reply to: May I ask Visualgdb when debugging the result output to the debugging window? De #12796

Yuex.S
Participant

It was nice to see Smartty, thank you.
Author

Posts

Viewing 15 posts - 1 through 15 (of 27 total)

1 2 →