[imanhp]

Hi again,

Its in the mbed.props file:

<PreprocessorDefinitions>TOOLCHAIN_GCC_ARM;TOOLCHAIN_GCC;MBED_CONF_EVENTS_PRESENT=1;__MBED__=1;TARGET_UVISOR_UNSUPPORTED;MBED_CONF_PLATFORM_DEFAULT_SERIAL_BAUD_RATE=9600;MBED_CONF_PLATFORM_STDIO_CONVERT_NEWLINES=0;TOOLCHAIN_object;TARGET_LIKE_MBED;TARGET_RELEASE;MBED_CONF_PLATFORM_STDIO_FLUSH_AT_EXIT=1;TARGET_RTOS_M4_M7;TARGET_DISCO_F746NG;ARM_MATH_CM7;DEVICE_INTERRUPTIN=1;TARGET_STM32F746;FEATURE_LWIP=1;MBED_BUILD_TIMESTAMP=1478563085.15;DEVICE_LOWPOWERTIMER=1;DEVICE_PORTINOUT=1;TARGET_STM32F7;TRANSACTION_QUEUE_SIZE_SPI=2;DEVICE_I2CSLAVE=1;DEVICE_RTC=1;DEVICE_PWMOUT=1;DEVICE_STDIO_MESSAGES=1;DEVICE_ANALOGIN=1;TARGET_FF_ARDUINO;TARGET_LIKE_CORTEX_M7;__MBED_CMSIS_RTOS_CM;__CMSIS_RTOS;DEVICE_SPI_ASYNCH=1;DEVICE_PORTIN=1;__FPU_PRESENT=1;TARGET_M7;DEVICE_SERIAL_ASYNCH=1;DEVICE_ANALOGOUT=1;DEVICE_I2C=1;DEVICE_PORTOUT=1;MBED_CONF_PLATFORM_STDIO_BAUD_RATE=9600;TARGET_STM;DEVICE_SERIAL=1;DEVICE_SPI=1;TARGET_STM32F746NG;TARGET_CORTEX_M;__CORTEX_M7;DEVICE_TRNG=1;DEVICE_SLEEP=1;DEVICE_CAN=1;DEVICE_SPISLAVE=1;MBED_CONF_RTOS_PRESENT=1;MBED_CONF_NORDIC_UART_HWFC=0;MBED_CONF_NORDIC_UART_HWFC=1;MBED_CONF_NORDIC_NRF_LF_CLOCK_SRC=NRF_LF_SRC_XTAL;MBED_CONF_NORDIC_UART_HWFC=0;MBED_CONF_NORDIC_UART_HWFC=1;MBED_CONF_NORDIC_NRF_LF_CLOCK_SRC=NRF_LF_SRC_XTAL;MBED_CONF_NORDIC_UART_HWFC=0;MBED_CONF_NORDIC_UART_HWFC=1;MBED_CONF_NORDIC_NRF_LF_CLOCK_SRC=NRF_LF_SRC_XTAL;MBED_CONF_LWIP_IPV6_ENABLED=0;MBED_CONF_NSAPI_PRESENT=1;MBED_CONF_LWIP_ADDR_TIMEOUT=5;MBED_CONF_LWIP_IPV4_ENABLED=1;CFSTORE_STORAGE_DISABLE=0;UNITY_INCLUDE_CONFIG_H;MBED_CONF_LWIP_IP_VER_PREF=4;MBED_CONF_LWIP_IPV6_ENABLED=0;MBED_CONF_LWIP_ADDR_TIMEOUT=5;MBED_CONF_LWIP_IPV4_ENABLED=1;MBED_CONF_LWIP_IP_VER_PREF=4;%(ClCompile.PreprocessorDefinitions)</PreprocessorDefinitions>

MBED_CONF_NORDIC_UART_HWFC is defined multiple times. In bold above.

The generation of the PreprocessorDefinitions seems to be buggy. I see several other duplicate definitions.

 

 

 

• This reply was modified 8 years ago by imanhp.
• This reply was modified 8 years ago by imanhp.

[imanhp]

I get hundreds of warnings:

“MBED_CONF_NORDIC_UART_HWFC” redefined STM D:\CODE\MBED\STM\<command-line> 1

Any clue of where the fault might be?

[imanhp]

Hi,

5.2 is is here – https://www.mbed.com/en/platform/mbed-os/releases/

Any progress yet?

[imanhp]

Any progress with this?

[Author]

Posts