[IanJ]

Hi,

It should also be noted that I can actually compile the source using NotePad++ NPPEXEC which means that NotePad++ I configure with an execution script which then controls the Arduino IDE using the IDE debug mode (C:\Program Files (x86)\Arduino-1.8.9\arduino_debug). In other words command line mode.

The NPP script is as follows,

COMPILE ONLY:
set arduino_path = “C:\Program Files (x86)\Arduino-1.8.9\arduino_debug”
cmd /c $(arduino_path) –verbose-build –board stm32duino:STM32F1:genericSTM32F103C:device_variant=STM32F103CB –verify $(FULL_CURRENT_PATH)

COMPILE & UPLOAD (STLINK):
set arduino_path = “C:\Program Files (x86)\Arduino-1.8.9\arduino_debug”
cmd /c $(arduino_path) –verbose-build –board stm32duino:STM32F1:genericSTM32F103C:device_variant=STM32F103CB –verbose-upload –upload $(full_current_path)

This works perfectly…….so again, I can’t see why VisualGDB cannot do the same thing.

Ian.

• This reply was modified 5 years, 1 month ago by IanJ.

[IanJ]

Hi,

I am sorry to go on about this, but it is just very curious why it compiles perfectly from the Arduino IDE……….Something is different.
I thought VisualGDB would replicate & control the Arduino IDE as if it was run independantly.
Ian.

Archiving built core (caching) in: C:\Users\Ian\AppData\Local\Temp\arduino_cache_707179\core\core_a390828b8d406d0a53f1ea72fe80c344.a
Linking everything together...
"C:\\Program Files (x86)\\Arduino-1.8.9\\portable\\packages\\arduino\\tools\\arm-none-eabi-gcc\\4.8.3-2014q1/bin/arm-none-eabi-g++" -Os -Wl,--gc-sections -mcpu=cortex-m3 "-TC:\\Program Files (x86)\\Arduino-1.8.9\\portable\\packages\\stm32duino\\hardware\\STM32F1\\2019.10.9\\variants\\generic_stm32f103c/ld/jtag.ld" "-Wl,-Map,C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340/VoltageSourceDigitalMini20bitV2_00_STM32.ino.map" "-LC:\\Program Files (x86)\\Arduino-1.8.9\\portable\\packages\\stm32duino\\hardware\\STM32F1\\2019.10.9\\variants\\generic_stm32f103c/ld" -o "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340/VoltageSourceDigitalMini20bitV2_00_STM32.ino.elf" "-LC:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340" -lm -lgcc -mthumb -Wl,--cref -Wl,--check-sections -Wl,--gc-sections -Wl,--unresolved-symbols=report-all -Wl,--warn-common -Wl,--warn-section-align -Wl,--warn-unresolved-symbols -Wl,--start-group "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\sketch\\VoltageSourceDigitalMini20bitV2_00_STM32.ino.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\U8x8lib.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_bitmap.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_box.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_buffer.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_circle.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_cleardisplay.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_d_memory.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_d_setup.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_font.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_fonts.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_hvline.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_input_value.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_intersection.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_kerning.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_line.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_ll_hvline.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_message.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_polygon.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_selection_list.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8g2_setup.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8log.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8log_u8g2.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8log_u8x8.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_8x8.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_byte.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_cad.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_a2printer.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_il3820_296x128.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ist3020.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ks0108.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_lc7981.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ld7032_60x32.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ls013b7dh03.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_max7219.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_pcd8544_84x48.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_pcf8812.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_pcf8814_hx1230.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_sbn1661.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_sed1330.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_sh1106_64x32.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_sh1106_72x40.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_sh1107.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_sh1108.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_sh1122.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1305.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1306_128x32.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1306_128x64_noname.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1306_48x64.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1306_64x32.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1306_64x48.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1306_96x16.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1309.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1317.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1322.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1325.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1326.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1327.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1329.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1606_172x72.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_ssd1607_200x200.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_st75256.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_st7565.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_st7567.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_st7586s_erc240160.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_st7586s_s028hn118a.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_st7588.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_st7920.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_t6963.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_uc1601.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_uc1604.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_uc1608.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_uc1610.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_uc1611.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_uc1617.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_uc1638.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_uc1701_dogs102.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_d_uc1701_mini12864.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_debounce.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_display.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_fonts.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_gpio.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_input_value.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_message.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_selection_list.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_setup.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_string.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_u16toa.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\U8g2\\clib\\u8x8_u8toa.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\TimedAction\\TimedAction.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\SPI\\SPI.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\EEPROM\\EEPROM.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\EEPROM\\flash_stm32.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\stm32sleep-master\\STM32Sleep.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\RTClock\\RTClock.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\RTClock\\utility\\rtc_util.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\Wire\\SoftWire.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\Wire\\Wire.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\libraries\\Wire\\utility\\WireBase.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\core\\board.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\core\\wirish\\boards.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\core\\wirish\\boards_setup.cpp.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\core\\wirish\\start.S.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\core\\wirish\\start_c.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\core\\wirish\\syscalls.c.o" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340\\core\\core.a" -Wl,--end-group
"C:\\Program Files (x86)\\Arduino-1.8.9\\portable\\packages\\arduino\\tools\\arm-none-eabi-gcc\\4.8.3-2014q1/bin/arm-none-eabi-objcopy" -O binary "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340/VoltageSourceDigitalMini20bitV2_00_STM32.ino.elf" "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340/VoltageSourceDigitalMini20bitV2_00_STM32.ino.bin"
Multiple libraries were found for "SPI.h"
Used: C:\Program Files (x86)\Arduino-1.8.9\portable\packages\stm32duino\hardware\STM32F1\2019.10.9\libraries\SPI
Not used: C:\Program Files (x86)\Arduino-1.8.9\libraries\SPI
Multiple libraries were found for "EEPROM.h"
Used: C:\Program Files (x86)\Arduino-1.8.9\portable\packages\stm32duino\hardware\STM32F1\2019.10.9\libraries\EEPROM
Not used: C:\Program Files (x86)\Arduino-1.8.9\libraries\EEPROM
Multiple libraries were found for "RTClock.h"
Used: C:\Program Files (x86)\Arduino-1.8.9\portable\packages\stm32duino\hardware\STM32F1\2019.10.9\libraries\RTClock
Not used: C:\Program Files (x86)\Arduino-1.8.9\libraries\RTClock
Multiple libraries were found for "Wire.h"
Used: C:\Program Files (x86)\Arduino-1.8.9\portable\packages\stm32duino\hardware\STM32F1\2019.10.9\libraries\Wire
Not used: C:\Program Files (x86)\Arduino-1.8.9\portable\packages\stm32duino\hardware\STM32F1\2019.10.9\libraries\WireSlave
Not used: C:\Program Files (x86)\Arduino-1.8.9\libraries\Wire
Using library U8g2 at version 2.23.18 in folder: C:\Users\Ian\Documents\Arduino\libraries\U8g2
Using library TimedAction in folder: C:\Program Files (x86)\Arduino-1.8.9\libraries\TimedAction (legacy)
Using library SPI at version 1.0 in folder: C:\Program Files (x86)\Arduino-1.8.9\portable\packages\stm32duino\hardware\STM32F1\2019.10.9\libraries\SPI
Using library EEPROM in folder: C:\Program Files (x86)\Arduino-1.8.9\portable\packages\stm32duino\hardware\STM32F1\2019.10.9\libraries\EEPROM (legacy)
Using library stm32sleep-master in folder: C:\Program Files (x86)\Arduino-1.8.9\libraries\stm32sleep-master (legacy)
Using library RTClock at version 1.0 in folder: C:\Program Files (x86)\Arduino-1.8.9\portable\packages\stm32duino\hardware\STM32F1\2019.10.9\libraries\RTClock
Using library Wire at version 1.0 in folder: C:\Program Files (x86)\Arduino-1.8.9\portable\packages\stm32duino\hardware\STM32F1\2019.10.9\libraries\Wire
"C:\\Program Files (x86)\\Arduino-1.8.9\\portable\\packages\\arduino\\tools\\arm-none-eabi-gcc\\4.8.3-2014q1/bin/arm-none-eabi-size" -A "C:\\Users\\Ian\\AppData\\Local\\Temp\\arduino_build_387340/VoltageSourceDigitalMini20bitV2_00_STM32.ino.elf"
Sketch uses 81832 bytes (62%) of program storage space. Maximum is 131072 bytes.
Global variables use 6552 bytes (31%) of dynamic memory, leaving 13928 bytes for local variables. Maximum is 20480 bytes.

• This reply was modified 5 years, 1 month ago by IanJ.
• This reply was modified 5 years, 1 month ago by IanJ.

[IanJ]

Hi,

Well I tried everything but couldn’t get it working…….The problem I think is more than just the hardware/tools/packages paths etc.

I’m no expert but…….
The main STM32Sleep.h library references some other files in other library folders and theres multiple options of MCU’s and hardware that the libraries seem to be a bit dynamic on selecting.
I tried copying some of the files I saw being referenced to my main STM32Sleep.h library folder and it cleared one error but then just presented more. I copied more files in but still never got to the end……
There are too many options for me to correctly decided on what exact ones I need, but then again I will just cause a lot of problems if I change to a slightly different MCU.

So, I’m at a bit of a crossroads…..I still have 3 weeks to test VisualGDB so I will try some more STM32 libraries and see what happens. All else fails it’s back to Arduino IDE & Notepad++.

Wishlist:…….the guys at SYSPROGS will install the same libraries as I have and see if they can get it working.

https://github.com/chacal/stm32sleep
https://github.com/stm32duino/Arduino_Core_STM32
Install STM32 core support via boards manager. I am using STM32F103

Ian.

[IanJ]

Hi,

Per above it didn’t work, in fact I got errors regarding STM32F1 config or something……..however, I had renamed the \Arduino15 folder under users as I don’t use it, and no matter how I tried to change the various Arduino settings to steer away from \Arduino15 it still wanted it.

So I got rid of my \portable folder and went back to having \Arduino15…….and I verified the Arduino IDE still compiled my source code (both folders have same contents anyways)……and then onto VisualGDB again.

I reset the XML again and set the IDE directory……..and I am back to libmaple/gpio.h: No such file or directory problem again.
(Out of interest I then I added the dan.drown.org json to Package Index URL’s to try but same problem.)

Here is the log again at this point, and the current arduino settings screenshot:-

Launching Arduino builder...
C:\Program Files (x86)\Sysprogs\VisualGDB\Arduino\arduino-builder.exe -prefs=com.sysprogs.extraflags="-ggdb" -compile -logger=machine -fqbn=STM32:stm32:GenF1:pnum=BLUEPILL_F103C8B,upload_method=swdMethod,xserial=generic,usb=none,xusb=FS,opt=osstd,rtlib=nano -build-path D:\Code_STM32\VoltageSourceDigitalMini20bitV2_00_STM32\Output\Generic_STM32F1_series\Debug -unoptimize=sketch -hardware "C:/Program Files (x86)/Arduino-1.8.9/hardware" -hardware C:\Users\Ian\AppData\Local/Arduino15/packages -tools "C:/Program Files (x86)/Arduino-1.8.9/tools-builder" -tools C:\Users\Ian\AppData\Local/Arduino15/packages -built-in-libraries "C:/Program Files (x86)/Arduino-1.8.9/libraries" -libraries C:\Users\Ian\Documents/Arduino/Libraries -prefs=runtime.tools.STM32Tools.path=C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\tools\STM32Tools\1.3.0 -prefs=runtime.tools.arm-none-eabi-gcc.path=C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\tools\arm-none-eabi-gcc\8.2.1-1.7 sketches/VoltageSourceDigitalMini20bitV2_00_STM32.ino sketches/DAC.ino sketches/Delay.ino sketches/EEprom.ino sketches/Interrupts.ino sketches/IO.ino sketches/keypad.ino sketches/keypadcalmode.ino sketches/keypadsettingsmode.ino sketches/Lcd.ino sketches/Newmap.ino sketches/SerialInterface.ino sketches/TimedActions.ino
info: Build options changed, rebuilding all
warn: Multiple libraries were found for "SPI.h"
warn: Used: C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\hardware\stm32\1.6.1\libraries\SPI
warn: Not used: C:\Program+Files+(x86)\Arduino-1.8.9\libraries\SPI
warn: Multiple libraries were found for "EEPROM.h"
warn: Used: C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\hardware\stm32\1.6.1\libraries\EEPROM
warn: Not used: C:\Program+Files+(x86)\Arduino-1.8.9\libraries\EEPROM
In file included from D:\Code_STM32\VoltageSourceDigitalMini20bitV2_00_STM32\sketches\VoltageSourceDigitalMini20bitV2_00_STM32.ino:28:
C:\Program Files (x86)\Arduino-1.8.9\libraries\stm32sleep-master/STM32Sleep.h:1:10: fatal error: libmaple/gpio.h: No such file or directory
#include <libmaple/gpio.h>
^~~~~~~~~~~~~~~~~
compilation terminated.
exit status 1
-------------------------------------------------------------
Command exited with code 1
Executable: C:\Program Files (x86)\Sysprogs\VisualGDB\Arduino\arduino-builder.exe
Arguments: -prefs=com.sysprogs.extraflags="-ggdb" -compile -logger=machine -fqbn=STM32:stm32:GenF1:pnum=BLUEPILL_F103C8B,upload_method=swdMethod,xserial=generic,usb=none,xusb=FS,opt=osstd,rtlib=nano -build-path D:\Code_STM32\VoltageSourceDigitalMini20bitV2_00_STM32\Output\Generic_STM32F1_series\Debug -unoptimize=sketch -hardware "C:/Program Files (x86)/Arduino-1.8.9/hardware" -hardware C:\Users\Ian\AppData\Local/Arduino15/packages -tools "C:/Program Files (x86)/Arduino-1.8.9/tools-builder" -tools C:\Users\Ian\AppData\Local/Arduino15/packages -built-in-libraries "C:/Program Files (x86)/Arduino-1.8.9/libraries" -libraries C:\Users\Ian\Documents/Arduino/Libraries -prefs=runtime.tools.STM32Tools.path=C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\tools\STM32Tools\1.3.0 -prefs=runtime.tools.arm-none-eabi-gcc.path=C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\tools\arm-none-eabi-gcc\8.2.1-1.7 sketches/VoltageSourceDigitalMini20bitV2_00_STM32.ino sketches/DAC.ino sketches/Delay.ino sketches/EEprom.ino sketches/Interrupts.ino sketches/IO.ino sketches/keypad.ino sketches/keypadcalmode.ino sketches/keypadsettingsmode.ino sketches/Lcd.ino sketches/Newmap.ino sketches/SerialInterface.ino sketches/TimedActions.ino
Directory: D:\Code_STM32\VoltageSourceDigitalMini20bitV2_00_STM32
Command-line action failed

========== Project Build Summary ==========
VoltageSourceDigitalMini20bitV2_00_STM32 built in 00:06
========== Build: 0 Succeeded, 1 Failed ==========

 

 

 

 

Attachments:

You must be logged in to view attached files.

[IanJ]

Text file attached….zipped this time.

Attachments:

You must be logged in to view attached files.

[IanJ]

Hi,

The Process Monitor will take me a bit of time to set up………meanwhile:-

Arduino settings screenshot attached.

Arduino IDE successful compile of exact same code built log text file attached…..not sure if any help to you.
The only other one that caused a problem is U8gslib.h which I had to add a path to in Arduino Settings as you’ll see.
Here’s the libs loaded at the top of my primarty .ino file for info:-
#include <U8g2lib.h>
#include <TimedAction.h>
#include <SPI.h>
#include <EEPROM.h>
#include <math.h> // not sure if need this on STM32
#include <STM32Sleep.h> // won’t work with VisualGDB for some reason

VisualGDB Build log:

Launching Arduino builder...
C:\Program Files (x86)\Sysprogs\VisualGDB\Arduino\arduino-builder.exe -prefs=com.sysprogs.extraflags="-ggdb" -compile -logger=machine -fqbn=STM32:stm32:GenF1:pnum=BLUEPILL_F103C8B,upload_method=swdMethod,xserial=generic,usb=none,xusb=FS,opt=osstd,rtlib=nano -build-path D:\Code_STM32\VoltageSourceDigitalMini20bitV2_00_STM32\Output\Generic_STM32F1_series\Debug -unoptimize=sketch -hardware "C:/Program Files (x86)/Arduino-1.8.9/hardware" -hardware "C:\Program Files (x86)\Arduino-1.8.9\hardware" -hardware "C:/Program Files (x86)/Arduino-1.8.9/portable/packages/STM32/hardware" -hardware C:\Users\Ian\AppData\Local/Arduino15/packages -tools "C:/Program Files (x86)/Arduino-1.8.9/tools-builder" -tools "C:\Program Files (x86)\Arduino-1.8.9\tools" -tools C:\Users\Ian\AppData\Local/Arduino15/packages -built-in-libraries "C:\Program Files (x86)\Arduino-1.8.9\libraries" -libraries "C:\Program Files (x86)\Arduino-1.8.9\libraries" -libraries "C:/Program Files (x86)/Arduino-1.8.9/libraries/u8g2/" -libraries "C:\Program Files (x86)\Arduino-1.8.9\libraries\STM32duino-bootloader-master\Arduino_STM32-Drivers" -prefs=runtime.tools.STM32Tools.path=C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\tools\STM32Tools\1.3.0 -prefs=runtime.tools.arm-none-eabi-gcc.path=C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\tools\arm-none-eabi-gcc\8.2.1-1.7 sketches/VoltageSourceDigitalMini20bitV2_00_STM32.ino sketches/DAC.ino sketches/Delay.ino sketches/EEprom.ino sketches/Interrupts.ino sketches/IO.ino sketches/keypad.ino sketches/keypadcalmode.ino sketches/keypadsettingsmode.ino sketches/Lcd.ino sketches/Newmap.ino sketches/SerialInterface.ino sketches/TimedActions.ino
A subdirectory or file D:\Code_STM32\VoltageSourceDigitalMini20bitV2_00_STM32\Output\Generic_STM32F1_series\Debug\sketch already exists.
In file included from D:\Code_STM32\VoltageSourceDigitalMini20bitV2_00_STM32\sketches\VoltageSourceDigitalMini20bitV2_00_STM32.ino:28:
C:\Program Files (x86)\Arduino-1.8.9\libraries\stm32sleep-master/STM32Sleep.h:1:10: fatal error: libmaple/gpio.h: No such file or directory
#include <libmaple/gpio.h>
^~~~~~~~~~~~~~~~~
warn: Multiple libraries were found for "SPI.h"
warn: Used: C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\hardware\stm32\1.6.1\libraries\SPI
warn: Not used: C:\Program+Files+(x86)\Arduino-1.8.9\libraries\SPI
warn: Multiple libraries were found for "EEPROM.h"
warn: Used: C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\hardware\stm32\1.6.1\libraries\EEPROM
warn: Not used: C:\Program+Files+(x86)\Arduino-1.8.9\libraries\EEPROM
compilation terminated.
exit status 1
-------------------------------------------------------------
Command exited with code 1
Executable: C:\Program Files (x86)\Sysprogs\VisualGDB\Arduino\arduino-builder.exe
Arguments: -prefs=com.sysprogs.extraflags="-ggdb" -compile -logger=machine -fqbn=STM32:stm32:GenF1:pnum=BLUEPILL_F103C8B,upload_method=swdMethod,xserial=generic,usb=none,xusb=FS,opt=osstd,rtlib=nano -build-path D:\Code_STM32\VoltageSourceDigitalMini20bitV2_00_STM32\Output\Generic_STM32F1_series\Debug -unoptimize=sketch -hardware "C:/Program Files (x86)/Arduino-1.8.9/hardware" -hardware "C:\Program Files (x86)\Arduino-1.8.9\hardware" -hardware "C:/Program Files (x86)/Arduino-1.8.9/portable/packages/STM32/hardware" -hardware C:\Users\Ian\AppData\Local/Arduino15/packages -tools "C:/Program Files (x86)/Arduino-1.8.9/tools-builder" -tools "C:\Program Files (x86)\Arduino-1.8.9\tools" -tools C:\Users\Ian\AppData\Local/Arduino15/packages -built-in-libraries "C:\Program Files (x86)\Arduino-1.8.9\libraries" -libraries "C:\Program Files (x86)\Arduino-1.8.9\libraries" -libraries "C:/Program Files (x86)/Arduino-1.8.9/libraries/u8g2/" -libraries "C:\Program Files (x86)\Arduino-1.8.9\libraries\STM32duino-bootloader-master\Arduino_STM32-Drivers" -prefs=runtime.tools.STM32Tools.path=C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\tools\STM32Tools\1.3.0 -prefs=runtime.tools.arm-none-eabi-gcc.path=C:\Users\Ian\AppData\Local\Arduino15\packages\STM32\tools\arm-none-eabi-gcc\8.2.1-1.7 sketches/VoltageSourceDigitalMini20bitV2_00_STM32.ino sketches/DAC.ino sketches/Delay.ino sketches/EEprom.ino sketches/Interrupts.ino sketches/IO.ino sketches/keypad.ino sketches/keypadcalmode.ino sketches/keypadsettingsmode.ino sketches/Lcd.ino sketches/Newmap.ino sketches/SerialInterface.ino sketches/TimedActions.ino
Directory: D:\Code_STM32\VoltageSourceDigitalMini20bitV2_00_STM32
Command-line action failed

========== Project Build Summary ==========
VoltageSourceDigitalMini20bitV2_00_STM32 built in 00:07
========== Build: 0 Succeeded, 1 Failed ==========

Ian.

 

Attachments:

You must be logged in to view attached files.

[Author]

Posts