esp32dude

Forum Replies Created

Viewing 3 posts - 1 through 3 (of 3 total)
  • Author
    Posts
  • in reply to: ESP32 toolchain test failed #27877
    esp32dude
    Participant

    yes I did.

    In the meantime I found out what causes my issue:

    1. I forgot a decoupling cap at the ESP32 3.3V pin.
    2. The JTAG mini 10 pole cable/connector is a little bit unstable it seems.

    Now, sometimes the upload works, sometimes it does not. Not sure if OpenGDB combined with a non natively supported J-Link also add to this unstable behavior.

     

    • This reply was modified 4 years, 5 months ago by esp32dude.
    in reply to: ESP32 toolchain test failed #27825
    esp32dude
    Participant

    J-Link works with dev boards like ESP32-WROVER.

    The issue is, I have a custom board and only have the JTAG interface. Maybe you can have a look at the ESP32 schematic if you see any issue?

    • This reply was modified 4 years, 6 months ago by esp32dude.
    in reply to: ESP32 toolchain test failed #27823
    esp32dude
    Participant

    I was following this tutorial: https://visualgdb.com/tutorials/esp32/wroom/

    There it was suggested to use Embedded wizard.

    Anyways, for ESP-IDF wizard, I cannot connect to ESP32 over J-Link. I checked the pinning, it is correct.

    Here is the error log:

    C:\Users\XXXXX\AppData\Local\VisualGDB\EmbeddedDebugPackages\com.sysprogs.esp32.core\bin\openocd.exe -c “gdb_port 50443” -c “telnet_port 50444” -f interface/jlink.cfg -c “adapter_khz 3000” -f target/esp32.cfg -c “echo VisualGDB_OpenOCD_Ready”
    Open On-Chip Debugger 0.10.0 (2019-10-24)
    Licensed under GNU GPL v2
    libusb1 09e75e98b4d9ea7909e8837b7a3f00dda4589dc3
    For bug reports, read
    http://openocd.org/doc/doxygen/bugs.html
    adapter speed: 3000 kHz
    Info : Configured 2 cores
    VisualGDB_OpenOCD_Ready
    Info : Listening on port 6666 for tcl connections
    Info : Listening on port 50444 for telnet connections
    Error: type ‘esp32’ is missing virt2phys
    Warn : Failed to open device: LIBUSB_ERROR_NOT_SUPPORTED.
    Info : J-Link V11 compiled Aug 14 2019 16:21:09
    Info : Hardware version: 11.00
    Info : VTarget = 0.000 V
    Info : clock speed 3000 kHz
    Error: JTAG scan chain interrogation failed: all ones
    Error: Check JTAG interface, timings, target power, etc.
    Error: Trying to use configured scan chain anyway…
    Error: esp32.cpu0: IR capture error; saw 0x1f not 0x01
    Warn : Bypassing JTAG setup events due to errors
    Info : Listening on port 50443 for gdb connections
    Info : accepting ‘gdb’ connection on tcp/50443
    Error: No symbols for FreeRTOS
    Error: Target not examined yet

    Error: Target not halted
    Error: auto_probe failed
    Error: Connect failed. Consider setting up a gdb-attach event for the target to prepare target for GDB connect, or use ‘gdb_memory_map disable’.
    Error: attempted ‘gdb’ connection rejected

Viewing 3 posts - 1 through 3 (of 3 total)